November 2010 Geek of All Trades: Windows 7 Deployment in 7 Easy Steps. Geek of All Trades: Windows 7 Deployment in 7. Configure WDS for Over-the-Network.

Is it possible to install Windows 7 ( Current RTM Version) on a computer without using removable media like DVD or USB? Dalton School Drivers Ed. The first thing that comes to my mind is through the network, but I don't have experience of doing a fresh install of Windows 7 via the network.

How to install Windows 7 via the network without any removable media? I know some may think that doing so, is just a waste of time and it's easier to do it with removable media, but in the current situation the target PC neither has CD/DVD Drive nor supports booting from USB. And in addition to that, the target computer is connected to the network via a wireless connection (I don't know if it will cause any problems with the installation).

I just did this (2011-04-01), and this question consistently ranked high in my googling, so I'll throw down a way-after-the-fact answer with the notes about what I learned. Hopefully this will fill in some blanks. Source OS was Win7 x64. Source machine: This machine must have a static IPv4 address. This example will use 192.168.0.1. This machine must have a Windows installation in a shared folder somewhere.

This example will use. Win7 This example will log in to the source machine with user TEST and password test. Luca Visual Fx Keygen For Mac on this page. Use tftpboot to fire up a DHCP server (gives an IP to a computer when requested). This will also start a TFTP server for all of the file transfers. There should be a folder called boot in the tftpboot directory which contains an installation of Windows PE.

Start tftpd64.exe (or tftpd32.exe), open the settings, use default settings, and change: • IP pool starting addresss: Whatever, the pool of IPs to draw from • Size of pool: Must be >2 • Boot File: boot pxeboot.com (will dump into Windows PE environment) • Mask: 255.255.255.0 works fine. • Uncheck 'Ping address before assignation' • Check 'Bind DHCP to this address' Restart the program to ensure changes are in effect. Receiver machine: Run a network boot from the receiver machine.

(The DHCP server will assign an IP). The boot file will be transferred and run.

Press F12 to tell Windows PE to do something. Wait a while (30-60 seconds). A command prompt will appear and load.

Wait until a cursor is available. A drive must be assigned to the root folder on the Source machine. To do this: X: Windows system32>net use z: 192.168.0.1 win7 A username of a user on the source machine, and password, must be entered. Enter the user name for '192.168.0.1': 192.168.0.1 TEST Enter the password for 192.169.0.1: test The command completed successfully.

Navigate over to the new directory ( z: ) and fire away. Commands will have a long delay but should work eventually. Links: (DHCP server x86 or x64, no boot dir) WinPE link removed. Everyone who has tried this, can testify how hard it is to pull it off. Recently, I had the same problem to solve and I have done lots of reading and testing.

In the end, the simplest tool for the job is. At least in my opinion.

But even Serva is prone to failure. You will need a lot of work to get it to work.

Also, its documentation is rather poorly structured and technical. So it is not that easy to understand how to set it up. That's why I decided to give it a try and document the whole process myself, including the issues people are most likely to encounter.

Since the whole thing is so complex, I published a long step by step guide: I hope some people will find it useful. If you have a Linux server, (AMAHI.org) mount you install DVD and edit your Samba config file - # 'nano /etc/samba/smb.conf'. Add the lines at the bottom -[DVD] enter then path = /media/UDF Volume/ then enter again and add - guest ok = yes enter Control X then y to save and enter to exit. Then from you client got to network connections - shares and there you will find the image files. If after copying of file your computer reboots and seems like it hangs just wait 10 more minutes and then if it still isn't doing anything reboot, but do not touch any keys. Wait and watch for the balloons to start over starting windows.